Stator for Scooter Aprilia Scarabeo 50 100 4T / Piaggio Fly Liberty Zip Free Skipper / Vespa ET4 LX 50 S / 2000-2013
Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.
- 2013 Vespa S 50
- 2013 Piaggio Fly 50
- 2012 Vespa S 50
- 2012 Vespa LX 50
- 2012 Piaggio Fly 50
- 2011 Vespa S 50
- 2011 Vespa LX 50
- 2011 Piaggio Fly 50
- 2010 Vespa S 50
- 2010 Vespa LX 50
- 2010 Piaggio Fly 50
- 2010 Aprilia Scarabeo 50 4T
- 2009 Vespa S 50
- 2009 Vespa LX 50
- 2009 Piaggio Fly 50
- 2009 Aprilia Scarabeo 50 4T
- 2009 Aprilia Scarabeo 100 4T
- 2008 Vespa S 50
- 2008 Vespa LX 50
- 2008 Piaggio Fly 50
- 2008 Aprilia Scarabeo 50 4T
- 2008 Aprilia Scarabeo 100 4T
- 2007 Vespa LX 50
- 2007 Piaggio Fly 50
- 2007 Aprilia Scarabeo 50 4T
- 2007 Aprilia Scarabeo 100 4T
- 2006 Vespa LX 50
- 2006 Piaggio Zip 50
- 2006 Piaggio Liberty 50
- 2006 Piaggio Fly 50
- 2006 Aprilia Scarabeo 50 4T
- 2006 Aprilia Scarabeo 100 4T
- 2005 Piaggio Zip 50
- 2005 Piaggio Liberty 50
- 2005 Piaggio Fly 50
- 2005 Aprilia Scarabeo 50 4T
- 2004 Piaggio Zip 50
- 2004 Piaggio Liberty 50
- 2004 Aprilia Scarabeo 50 4T
- 2004 Aprilia Scarabeo 100 4T
- 2003 Piaggio Zip 50
- 2003 Piaggio Skipper 150
- 2003 Piaggio Liberty 50
- 2003 Piaggio Free 100
- 2003 Aprilia Scarabeo 50 4T
- 2003 Aprilia Scarabeo 100 4T
- 2002 Vespa ET4 50
- 2002 Piaggio Zip 50
- 2002 Piaggio Skipper 125
- 2002 Piaggio Liberty 50
- 2002 Piaggio Free 100
- 2002 Aprilia Scarabeo 50 4T
- 2002 Aprilia Scarabeo 100 4T
- 2001 Vespa ET4 50
- 2001 Piaggio Zip 50
- 2001 Piaggio Skipper 150
- 2001 Piaggio Skipper 125
- 2001 Piaggio Liberty 50
- 2001 Aprilia Scarabeo 100 4T
- 2000 Vespa ET4 50
- 2000 Piaggio Zip 50
- 2000 Piaggio Skipper 150
- 2000 Piaggio Skipper 125
- 2000 Piaggio Liberty 50
AP8551076
Dimensions :
Interior diameter : 32 mm
Exterior diameter : 82 mm
Thickness : 10 mm
Length of wires stator to plug : 170 mm
Other specifications :
Number of wires : 2
Number of plugs : 1
Number of pins : 2
Wire to wire resistance :
Alternator : Black To Ground = 0.8 ohms +-20%
Pickup : Brown To Ground = 150 ohms +-20%
Before installing your new stator
- Check the AC output of the stator
- Replace any burned or corroded connectors on stator and regulator rectifier
- Check and repair any melted wiring
- Use hi-temp dielectric grease on all connectors
Our stator may use a different wire color code than your original.
All the wires are installed in the correct order; please do not change any of the wiring configurations.
This stator is designed as a direct plug-in replacement and should be used as such.
When bolting stator in, always use locking compound.
If our stator includes a pickup coil, always make sure the air gap is correct upon installation; we suggest as close as possible no less than 0.010".
Brand new aftermarket stator
- Direct replacement to your original unit
- Plug-and-play, direct fit, easy installation
- Highest grade of lamination materials
- Highest grade of copper winding, resistant to 200 degrees Celsius
- Pick up pulsar coil included
- Connector included
- All products shipped are tested
All item pictures are accurate; if in doubt, do not hesitate to compare our item to your original part.