0 item (CA$0.00)
Brand new stator
- Direct replacement to your original unit
- Plug-and-play, direct fit, easy installation.
- Highest grade lamination materials
- Highest grade copper windings, resistant to 200 degrees Celsius.
- Connector included
- All product shipped are tested
*All item pictures are accurate; if in doubt do not hesitate to compare our item to your original part.
Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.
Details
Brand new stator
- Direct replacement to your original unit
- Plug-and-play, direct fit, easy installation.
- Highest grade lamination materials
- Highest grade copper windings, resistant to 200 degrees Celsius.
- Connector included
- All product shipped are tested
*All item pictures are accurate; if in doubt do not hesitate to compare our item to your original part.
Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.
Videos
How Charging / Ignition / Starting Systems Work
How to repair your connectors like a pro!
RMSTATOR Corporate Video
Specifications
Dimensions :
Interior diameter : 48 mm
Exterior diameter : 115 mm
Thickness : 21 mm
Other specifications :
Number of wires : 7
Number of pins : 10
Wire to wire resistance :
Alternator : Yellow to Yellow = 0.2 ohms+/-20%
Fuel Pump : White/Blue to White/Blue = 17.2 ohms+/-20%
Hand Warmer Coils : Orange to Orange = 2 ohms+/-20%
Source Coil 1 : Green to Brown = 10 ohms+/-20%
Source Coil 2 : Green to Black = 10 ohms+/-20%
OEM # Replacement
Fits models
- Snowmobile
- 2005
- Arctic Cat
- Pantera 600 EFI L/C
- Arctic Cat
- 2004
- Arctic Cat
- Mountain Cat 600 EFI L/C
- Pantera 600 EFI L/C
- Arctic Cat
- 2003
- Arctic Cat
- Mountain Cat 600 EFI L/C
- Pantera 600 EFI L/C
- ZL 600 EFI L/C
- ZL 600 ESR EFI L/C
- ZL 600 SS ESR EFI L/C
- ZL 600 SS INTL
- Arctic Cat
- 2002
- Arctic Cat
- Mountain Cat 600 EFI L/C
- Pantera 600 EFI L/C
- ZL 600 EFI L/C
- ZL 600 ESR EFI L/C
- ZL 600 SS
- ZL 600 SS ESR EFI L/C
- ZL 600 SS INTL
- ZR 600 EFI L/C
- Arctic Cat
- 2001
- Arctic Cat
- Mountain Cat 500 EFI L/C
- Mountain Cat 600 EFI L/C
- ZL 500 EFI L/C
- ZL 600 EFI L/C
- ZL 600 ESR EFI L/C
- ZR 500 EFI L/C
- ZR 500 ESR EFI L/C
- ZR 600 EFI L/C
- Arctic Cat
- 2000
- Arctic Cat
- Powder 600 Special LE EFI L/C
- ZL 600 EFI L/C
- ZR 600 EFI L/C
- Arctic Cat
- 2005
Installation instructions
- Check the AC output of the stator.
- Replace any burned or corroded connectors on stator and regulator/rectifier
- Check and repair any melted wiring.
- Use hi-temp dielectric grease on all connectors
Our stator may use a different wire color code than your original.
All of the wires are installed in the correct order; please do not change any of the wiring configurations.
This stator is designed as a direct plug-in replacement and should be used as such.
When bolting stator in, always use locking compound.
If our stator includes a pickup coil, always make sure the air gap is correct upon installation; we suggest as close as possible no less than 0.010".