Menu

Worldwide USA & International Customer?  Go to International Store

X

Based on your location and your browser preferences, we suggest the following regional preferences:

English, Worldwide

Customer Service 1-877-838-1399 - 8AM-5PM EST Mon-Thu & 8AM-4PM EST Fri

Cart

0 item (CA$0.00)

X

You are currently searching with filters

Kit Stator + Voltage Regulator Rectifier For Suzuki Boulevard S83 / GL Intruder VS1400 1996-2009

RMS900-100114
RMSTATOR

Kit Stator + Voltage Regulator Rectifier For Suzuki Boulevard S83 / GL Intruder VS1400 1996-2009

RMS900-100114
RMSTATOR
Exact fit

Availability: In stock

Price: CA$287.00

OR
YOU SAVE 15% off the items price combined, when buying a kit.

Brand New Kit Stator + Voltage Regulator Rectifier

  • Direct replacement to your original unit
  • Plug-and-play, direct fit, easy installation.
  • Connector included
  • All products shipped are tested
  • One year limited warranty

All item pictures are accurate; if in doubt do not hesitate to compare our item to your original part.

Stator
  • Highest grade lamination materials
  • Highest grade copper windings, resistant to 200 degrees Celsius.
  • Pick up pulsar coil included
  • Rubber grommet included

20% MORE OUTPUT OVER STOCK, WORKS WITH ALL OTHER OEM COMPONENTS.

We have even included the opposite connector (main harness side) as we know these are often melted/corroded/defective and a major cause for repetitive electrical issues.

Voltage Regulator Rectifier
  • The Quality exceeds the OEM equipment
  • Improved heat sink and charging capabilities
  • Higher grade of electric components.

Details

YOU SAVE 15% off the items price combined, when buying a kit.

Brand New Kit Stator + Voltage Regulator Rectifier

  • Direct replacement to your original unit
  • Plug-and-play, direct fit, easy installation.
  • Connector included
  • All products shipped are tested
  • One year limited warranty

All item pictures are accurate; if in doubt do not hesitate to compare our item to your original part.

Stator
  • Highest grade lamination materials
  • Highest grade copper windings, resistant to 200 degrees Celsius.
  • Pick up pulsar coil included
  • Rubber grommet included

20% MORE OUTPUT OVER STOCK, WORKS WITH ALL OTHER OEM COMPONENTS.

We have even included the opposite connector (main harness side) as we know these are often melted/corroded/defective and a major cause for repetitive electrical issues.

Voltage Regulator Rectifier
  • The Quality exceeds the OEM equipment
  • Improved heat sink and charging capabilities
  • Higher grade of electric components.

Videos

Specifications

Stator

Dimensions :
Interior diameter : 54mm
Exterior diameter : 115mm
Thickness : 18mm
Length of wires stator to grommet : 200mm
Length of wires grommet to plug : 620mm
Length of pickup coil's wire to grommet : 90mm & 170mm

Other specifications :
Number of wires : 7
Number of plugs : 2
Number of pins : 7

Wire to wire resistance :
Alternator : Yellow between each Yellow = 0.4 ohms +/-20%
Pickup : Blue to Green = 200 ohms +/-20%
Source : Black to Yellow = 200 ohms +/-20%

Voltage Regulator Rectifier

Dimensions:
Width: 50mm
Length: 145mm
Height: 25mm
Wires length: 440mm

Other specifications:
Number of plugs: 1
Number of pins: 5
Number of wires: 5
Minimum Charging Voltage: 14.5V +/- 0.5V
Maximum Charging Current: 50A/500W
Open Circuit Voltage: <15V
Operation Temperature: -20⁰ to 85⁰

OEM # Replacement

RMS900-100114-R00

Fits models

Installation instructions

Stator + Voltage Regulator Rectifier

Before installing your new stator and voltage regulator rectifier

  • Check the AC output of the stator.
  • Replace any burned or corroded connectors on stator and regulator/rectifier
  • Check and repair any melted wiring.
  • Use hi-temp dielectric grease on all connectors

Our stator may use a different wire color code than your original.
All of the wires are installed in the correct order; please do not change any of the wiring configurations.
This stator is designed as a direct plug-in replacement and should be used as such.
When bolting stator in, always use locking compound.
If our stator includes a pickup coil, always make sure the air gap is correct upon installation; we suggest as close as possible no less than 0.010’’.

Reviews

Q&A